DIY Car Brake Fog Light Strobe Controller — купить онлайн / Недорогой интернет-магазин DealExtreme
DealExtreme
Недорогой интернет-магазин с бесплатной доставкой

Dealextreme аналог

диэлэкстим купить

Аксессуары для авто

Автомобильные лампочки Средства ухода Интерьер GPS-навигаторы Экстерьер Авто-гаджеты
Автоинверторы
Аудио системы Мониторы и DVD-плееры Автодиагностика Запчасти и компоненты Автобезопасность Системы слежения за авто
Мотоциклисту

DIY Car Brake Fog Light Strobe Controller

DIY Car Brake Fog Light Strobe Controller
Цена: 278 руб.

Вы можете приобрести этот товар по более низкой цене на Aliexpress.com:

decrease increase
Добавить в корзину
  • DIY Car Brake Fog Light Strobe Controller
  • DIY Car Brake Fog Light Strobe Controller
  • DIY Car Brake Fog Light Strobe Controller

Описание товара

Brand Jtron
Quantity 1 piece(s)
Material Glass fiber
Color Black + Red
Function Strobe brake light / fog light / strobe line
Other Features Output Current: 20 ~ 400mA (preferably not more than normal 400mA); Dimensions: 1.4cm long * 0. 9cm width * 0.8cm height; Description: This strobe circuit board can be used without modification function of the LED strobe lights, and other LED lighting devices. Burst flash chip with a new generation of high-current control transistor, the maximum safe output current is 400mA, strobe effect, full-chip process design, small size super large-capacity capacitor line filter, high-grade red FR4 PCB. Note: This board without a constant and can not be directly connected to the LED lamp requires limiting series resistors, resistor size by controlling the current size. Strobe Mode: This board is dual-mode burst flash control mode Always one end, the other end strobe mode. If used as brake lights for double wire or double contact, driving is lit (low light), brake when Strobe (highlighted). With a single burst flash mode, strobe terminal directly connected to, the power to start (highlighted) strobe. Strobe frequency: 6 times per second, fast flash off half a second cycle.
Packing List 1 x DIY Strobe Controller
Dimensions: 0.55 in x 0.35 in x 0.31 in (1.4 cm x 0.9 cm x 0.8 cm)
Weight: 0.04 oz (1 g)

Добавить отзыв

Отзывы(0)

Пользовательские комментарии

Добавить комментарий


Нет комментариев

Контроллер лампы стоп-сигнала автомобиля/противотуманной фары / проблескового сигнала
Марка Jtron
Количество 1 часть (ы)
Материал Стекловолокно
Цвет Черный + красный
Функция Строб стоп-сигнал / противотуманная фара / строба
Другие особенности Выходной ток: 20 ~ 400 мА (желательно не больше, чем обычно 400 мА); Размеры: 1.4cm длина * 0.9 см ширина * высота 0,8 см; Описание: Эта плата строб схема может использоваться без модификации функции светодиодов строб и других светодиодных устройств освещения.ИМПУЛЬС ВСПЫШКИ чип с новым поколением сильноточной управляющий транзистор, максимально безопасной выходной ток 400 мА, эффект стробоскопа, полный процесс чип дизайн, небольшие размеры супер конденсатор большой емкости сетевого фильтра, высококачественные красные FR4 PCB.Примечание: Эта плата без постоянной и не может быть напрямую связан с Светодиодная лампа требует ограничения последовательных резисторов, резистор, контролируя размер текущего размера.Строб Режим: Эта доска двухрежимный срабатывания вспышки Режим управления Всегда одном конце, другой режим стробоскопа конца.При использовании в качестве стоп-сигналы для двойного провода или двойной контакт, вождение горит (низкой освещенности), тормоза при Strobe (выделено).С помощью одного режима срабатывания вспышки, вспышки терминала напрямую связано с, сила, чтобы начать (выделено) вспышки.Строб частота: 6 раз в секунду, быстрая вспышка выключена половина второго цикла.
Упаковочный лист 1 х DIY Контроллер стробирования
Размеры: 0,55 х 0,35 х 0,31 в (1,4 см х 0,9 см х 0,8 см)
Вес: 0,04 унции (1 г)

DIY Car Brake Fog Light Strobe Controller
Brand Jtron
Quantity 1 piece(s)
Material Glass fiber
Color Black + Red
Function Strobe brake light / fog light / strobe line
Other Features Output Current: 20 ~ 400mA (preferably not more than normal 400mA); Dimensions: 1.4cm long * 0. 9cm width * 0.8cm height; Description: This strobe circuit board can be used without modification function of the LED strobe lights, and other LED lighting devices. Burst flash chip with a new generation of high-current control transistor, the maximum safe output current is 400mA, strobe effect, full-chip process design, small size super large-capacity capacitor line filter, high-grade red FR4 PCB. Note: This board without a constant and can not be directly connected to the LED lamp requires limiting series resistors, resistor size by controlling the current size. Strobe Mode: This board is dual-mode burst flash control mode Always one end, the other end strobe mode. If used as brake lights for double wire or double contact, driving is lit (low light), brake when Strobe (highlighted). With a single burst flash mode, strobe terminal directly connected to, the power to start (highlighted) strobe. Strobe frequency: 6 times per second, fast flash off half a second cycle.
Packing List 1 x DIY Strobe Controller
Dimensions: 0.55 in x 0.35 in x 0.31 in (1.4 cm x 0.9 cm x 0.8 cm)
Weight: 0.04 oz (1 g)